Artesyn MVME2502 Installation and Use (April 2015) User Manual download pdf (Page 53)

Hardware Preparation and Installation

MVME2502 Installation and Use (6806800R96E)

The console settings for the MVME2502 are:

 Eight bits per character

 One stop bit per character

 Parity disabled (no parity)

 Baud rate of 9600 baud

Verify that hardware is installed and the power/peripheral cables connected are appropriate for

your system configuration.

Replace the chassis or system cover, reconnect the chassis to power source, and turn the

equipment power on.

1 2 ... 48 49 50 51 52 53 54 55 56 57 58 ... 165 166

MVME2502 1
Trademarks 2
Contact Address 2
Contents 3
List of Tables 10
List of Figures 13
About this Manual 15
Abbreviations 16
Conventions 17
Summary of Changes 19
Safety Notes 21
Operation 22
Installation 22
Cabling and Connectors 23
Sicherheitshinweise 25
Kabel und Stecker 28
Batterie 28
Umweltschutz 29
Introduction 31
1.2 Standard Compliances 33
1.3 Mechanical Data 35
1.4 Ordering Information 35
1.5 Product Identification 37
Chapter 2 39
2.1 Overview 39
Shipment Inspection 40
2.3 Requirements 41
2.3.2 Power Requirements 42
2.4 Configuring the Board 43
2.5 Installing Accessories 44
2.5.2 PMC/XMC Support 46
Installation Procedure 46
HDMNTKIT2 48
MVME2502 are: 53
Chapter 3 55
3.1 Board Layout 55
3.2 Front Panel 57
3.3 LEDs 58
Table 3-1 Front Panel LEDs 59
3.3.2 On-board LEDs 60
3.4 Connectors 61
3.4.1.3 USB Connector (J5) 63
3.4.1.4 VMEBus P1 Connector 64
IRQ4 ADD 35 NC NC 65
3.4.1.5 VMEBus P2 Connector 66
3.4.2 On-board Connectors 67
3.4.2.2 PMC Connectors 68
3.4.2.3 JTAG Connector (P6) 74
3.4.2.4 COP Connector P50(15) 75
3.4.2.5 XMC Connector (XJ1) 76
3.4.2.6 XMC Connector (XJ2) 77
3.5 Switches 79
4.2 Chipset 84
4.2.3 PCI Express Interface 85
4.2.9 DMA Controller 87
4.2.14 P2020 Strapping Pins 89
4.3 System Memory 92
4.4 Timers 92
4.5 Ethernet Interfaces 93
4.6 SPI Bus Interface 94
4.6.3 Firmware Redundancy 95
4.7 Front UART Control 97
4.8 Rear UART Control 98
4.9 PMC/XMC Sites 98
4.9.1 PMC Add-on Card 99
4.9.2 XMC Add-on Card 99
4.10 SATA Interface 100
4.11 VME Support 100
4.12 USB 100
C Devices 101
4.14 Reset/Control CPLD 102
4.15 Power Management 102
Functional Description 103
4.16 Clock Structure 104
4.17 Reset Structure 105
4.18 Thermal Management 105
4.19 Real-Time Clock Battery 106
4.20 Debugging Support 106
4.20.2 JTAG Chain and Board 107
4.20.3 Custom Debugging 108
Memory Maps and Registers 111
5.3 Flash Memory Map 112
5.4 Linux Devices Memory Map 112
5.5.1 PLD Revision Register 114
5.5.2 PLD Year Register 115
5.5.3 PLD Month Register 115
5.5.4 PLD Day Register 115
5.5.5 PLD Sequence Register 116
5.5.11 PLD Boot Bank Register 121
5.5.13 PLD Test Register 1 124
5.5.14 PLD Test Register 2 125
5.5.17 EMMC Reset Register 128
5.6 External Timer Registers 130
5.6.2 Control Registers 131
Boot System 135
6.3 Boot Options 136
6.6 Updating U-Boot 143
Programming Model 145
7.3 Interrupt Controller 149
7.4 I2C Bus Device Addressing 150
7.5 Ethernet PHY Address 150
7.6.1 MRAM 151
7.6.2 Real Time Clock 151
7.6.3 Quad UART 151
7.6.4 LBC Timing Parameters 152
7.7 Clock Distribution 153
7.7.1 System Clock 154
7.7.2 Real Time Clock Input 155
Replacing the Battery 157
Related Documentation 161
B.2 Manufacturers’ Documents 162
B.3 Related Specifications 162

Comments to this Manuals

No comments

Artesyn MVME2502 Installation and Use (April 2015) User Manual Page 53

Comments to this Manuals

Related products and manuals for Equipment Artesyn MVME2502 Installation and Use (April 2015)