Artesyn MVME2502 Installation and Use (April 2015) User Manual Page 39
- Page / 166
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 2
MVME2502 Installation and Use (6806800R96E)
39
Hardware Preparation and Installation
2.1 Overview
This chapter provides unpacking instructions, hardware preparation, installation procedures
of the board. Installation instructions for the optional PMC/XMC modules and transitions
modules are also included.
A fully implemented MVME2502 consists of the base board and the following modules:
PCI Mezzanine Card (PMC) or PCI-E Mezzanine Card (XMC) for added versatility
Rear transition module
SATA kit
NOTE: MVME2502-HDMNKIT1/MVME2502-HDMNKIT2 is provided based on purchase order.
The following are the steps to be performed before using the board. Be sure to read the entire
chapter, including all caution and warning notes, before you begin.
1. Unpack the hardware. Refer to Unpacking and Inspecting the Board on page 40
2. Configure the hardware by setting jumpers on the board and the RTM. Refer to Configuring
the Board on page 43
3. Install the rear transition module in the chassis. Refer to Rear Transition Module on page 44.
4. Install PMC module (if required). Refer to PMC/XMC Support on page 46.
5. Install XMC span module (if required). Refer to PMC/XMC Support on page 46.
6. If purchased, install MVME2502-HDMNKIT1/MVME2502-HDMNKIT2. Refer to Installation
of MVME2502-HDMNTKIT1/MVME2502-HDMNTKIT2 on page 48.
7. Install the board in the chassis. Refer to Installing and Removing the Board on page 50.
8. Attach cables and apply power. Refer to Completing the Installation on page 52.
- MVME2502 1
- Trademarks 2
- Contact Address 2
- Contents 3
- List of Tables 10
- List of Figures 13
- About this Manual 15
- Abbreviations 16
- Conventions 17
- Summary of Changes 19
- Safety Notes 21
- Operation 22
- Installation 22
- Cabling and Connectors 23
- Sicherheitshinweise 25
- Kabel und Stecker 28
- Batterie 28
- Umweltschutz 29
- Introduction 31
- 1.2 Standard Compliances 33
- 1.3 Mechanical Data 35
- 1.4 Ordering Information 35
- 1.5 Product Identification 37
- Chapter 2 39
- 2.1 Overview 39
- Shipment Inspection 40
- 2.3 Requirements 41
- 2.3.2 Power Requirements 42
- 2.4 Configuring the Board 43
- 2.5 Installing Accessories 44
- 2.5.2 PMC/XMC Support 46
- Installation Procedure 46
- HDMNTKIT2 48
- MVME2502 are: 53
- Chapter 3 55
- 3.1 Board Layout 55
- 3.2 Front Panel 57
- 3.3 LEDs 58
- Table 3-1 Front Panel LEDs 59
- 3.3.2 On-board LEDs 60
- 3.4 Connectors 61
- 3.4.1.3 USB Connector (J5) 63
- 3.4.1.4 VMEBus P1 Connector 64
- IRQ4 ADD 35 NC NC 65
- 3.4.1.5 VMEBus P2 Connector 66
- 3.4.2 On-board Connectors 67
- 3.4.2.2 PMC Connectors 68
- 3.4.2.3 JTAG Connector (P6) 74
- 3.4.2.4 COP Connector P50(15) 75
- 3.4.2.5 XMC Connector (XJ1) 76
- 3.4.2.6 XMC Connector (XJ2) 77
- 3.5 Switches 79
- 4.2 Chipset 84
- 4.2.3 PCI Express Interface 85
- 4.2.9 DMA Controller 87
- 4.2.14 P2020 Strapping Pins 89
- 4.3 System Memory 92
- 4.4 Timers 92
- 4.5 Ethernet Interfaces 93
- 4.6 SPI Bus Interface 94
- 4.6.3 Firmware Redundancy 95
- 4.7 Front UART Control 97
- 4.8 Rear UART Control 98
- 4.9 PMC/XMC Sites 98
- 4.9.1 PMC Add-on Card 99
- 4.9.2 XMC Add-on Card 99
- 4.10 SATA Interface 100
- 4.11 VME Support 100
- 4.12 USB 100
- C Devices 101
- 4.14 Reset/Control CPLD 102
- 4.15 Power Management 102
- Functional Description 103
- 4.16 Clock Structure 104
- 4.17 Reset Structure 105
- 4.18 Thermal Management 105
- 4.19 Real-Time Clock Battery 106
- 4.20 Debugging Support 106
- 4.20.2 JTAG Chain and Board 107
- 4.20.3 Custom Debugging 108
- Memory Maps and Registers 111
- 5.3 Flash Memory Map 112
- 5.4 Linux Devices Memory Map 112
- 5.5.1 PLD Revision Register 114
- 5.5.2 PLD Year Register 115
- 5.5.3 PLD Month Register 115
- 5.5.4 PLD Day Register 115
- 5.5.5 PLD Sequence Register 116
- 5.5.11 PLD Boot Bank Register 121
- 5.5.13 PLD Test Register 1 124
- 5.5.14 PLD Test Register 2 125
- 5.5.17 EMMC Reset Register 128
- 5.6 External Timer Registers 130
- 5.6.2 Control Registers 131
- Boot System 135
- 6.3 Boot Options 136
- 6.6 Updating U-Boot 143
- Programming Model 145
- 7.3 Interrupt Controller 149
- 7.4 I2C Bus Device Addressing 150
- 7.5 Ethernet PHY Address 150
- 7.6.1 MRAM 151
- 7.6.2 Real Time Clock 151
- 7.6.3 Quad UART 151
- 7.6.4 LBC Timing Parameters 152
- 7.7 Clock Distribution 153
- 7.7.1 System Clock 154
- 7.7.2 Real Time Clock Input 155
- Replacing the Battery 157
- Related Documentation 161
- B.2 Manufacturers’ Documents 162
- B.3 Related Specifications 162
Related products and manuals for Equipment Artesyn MVME2502 Installation and Use (April 2015)
(156 pages)© 2020, manymanuals.com. All rights reserved. | 1.481 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals